Despite their low weight and diminutive dimensions, the Matrix GT1000FX 1u and GT1000FX 2u 19" rack mount stereo power amps with MOSFET solid state technology offer the following advantages:
- Full, lively sound
- Excellent dynamics
- Power to cut through the mix
- 2x500 Watt stereo / 1000 Watt mono
- Minimal heat development
- No humming
- High output
- Lots of headroom
- Bridge and mono modes
- Safeguarded against incorrect use
- Flexible connections for various impedances and cabinets
ONE THOUSAND WATTS
Not many guitarists will ever need 1000 Watts, but having that much power in reserve with so much headroom and dynamics behind you is both impressive and reassuring. On top of this both the 1u and 2u versions of the GT1000FX power amps are extremely flexible when it comes to connecting up cabinets with differing impedences. In bridged mode both power amp modules are combined into one single power monster.
- 2 x 350 Watts to 8 Ohm
- 2 x 500 Watts to 4 Ohm
- 650 Watts in bridged mode to 16 ohms
- 1000 Watts im bridged mode to 8 ohms
And all this comes with a signal-to-noise ratio of 96 dB and a THD (total harmonic distortion) of just 0.06% at 1kHz, or <0.1% between 20Hz and 20kHz at full power!
1 OR 2 UNITS
The space-saving and light (only 3.7kg) 1u version of the GT1000FX with 1000 Watts is ideal for live use. The 2u version weighs just over four kilos and due to its larger, quieter fans it is the perfect choice for studios or any other environment where ultra-quiet operation is paramount. Apart from the fans and the housing height the two machines are built identically.
The Matrix GT1000FX power amps were developed specifically with guitarists in mind. They are ideal for use with all the Axe-Fx versions and are highly recommended by Fractal Audio. Of course they also work brilliantly with other amp and effects modellers, tube preamps, modelling amps with line-out jacks and as slave amps.
They can do loud, they can do quiet and, should the need arise, they can do really, really loud as well. Punch, dynamics and great sound that really cuts through, in a way that gets every guitarist's heart going.
Aside from the obvious power socket, the Matrix GT1000FX offers five connection jacks. Per channel there is one Neutrik combi 1/4 inch/XLR input and a combi 1/4inch/Speakon output and for the bridge mode there is also a dedicated 1/4inch/Speakon output.
SPEAKERS AND IMPEDANCE
Any suitable loudspeaker cabinets can easily be connected to the Matrix GT1000FX. The user is completely free to decide whether to use a full-range passive monitor or a guitar cabinet, either with or without speaker/cabinet simulation.
NICE TO GUITARISTS
When it comes to connecting up loudspeaker cabs the Matrix is extremely guitarist-friendly, tolerant and flexible. Using a 2x12 box with one 8 ohm speaker and one 16 ohm speaker in mono is no problem, nor is using a 4 ohm cabinet on one side and a 16 ohm cab on the other side in stereo mode. Per channel you can run any speakers (or speaker combinations) with a minimum impedance of 4 ohms and in bridged mode the minimum impedence is 8 ohms.
STEREO - MONO - BRIDGED MODE
- The rear panel holds a switch for the three output modes. The selected mode is shown on the front panel LEDs:
- In stereo mode channels A and B can be run independently and can be fed by different signals.
- In parallel mono mode input A feeds both channels and both power amps. Input B has no use here. Both channels can still be adjusted separately for volume.
- In bridged mode (mono) the input signal from channel A is sent out of phase to channel B. There is a dedicated loudspeaker jack for bridged mode (mono).
- A special Soft Start Circuit ensures that when the unit is switched on it draws its power slowly to avoid tripping the house circuit breaker.
- There is built-in protection against loudspeaker short circuits and overheating.
- Power-on thump is avoided with a relais-controlled delay in the connection of the speakers.
- There is no physical connection with the speakers until the unit has powered up.